ASK A BRAND

Onkyo TX-SV Receiver subwoofer pre out no sound Yes turing on the “A” speaker is required for the Onkyo, but that only turns on the 2 front speakers in the “A” speaker jacks. You may also need to check and see if the Onkyo has a menu selection in the setup menu that will turn on the sub woofer output on the back of the receiver. I have seen on countless occasions where people just have a hard time finding that sub woofer option on their receiver. I do not have the manuals for this Onkyo, so I can not tell you the exact way to find it. I have been repairing surround receivers since they have been on the market and beleive me, you are not alone in this situation. Sometimes it seems like you need a Phd. The solution should be in your owners manual, with the problem then being, just where in the manual. Go slowly thru it paying the closest attention to anything about set up procedures. I have also seen at times where the setup for the sub-woofer is not listed as sub-woofer, but as “LFE” low frequency effect.

Can I hook my car subwoofer up to my home audio receiver?

The format was first unveiled back in and installed in a select group of movie theaters around the world. Since then, over movies have been encoded and released in the object-based three dimensional surround sound format. Now, Dolby and its partners in consumer electronics are bringing that same theatrical experience to the living room or dedicated home theater.

But if you want to bring the Dolby Atmos experience home, you’re going to need to upgrade some of your gear.

A channel A/V receiver like the Sony STR-DH lets you hook up seven speakers and up to two subwoofers, giving you a boosted surround sound setup with two additional positional speakers.

We reached out to the head of engineering at AxiomAudio. So you just got a new subwoofer and want to ensure you squeeze every ounce of bass from it, right? But the way a subwoofer sounds and interacts with a typical listening room can be a very complex subject. There are all kinds of tools and measurement systems and other apps that will allow you to get very precise ideas of where you can place the subwoofer for the best response. Conventional wisdom says that you want to take your subwoofer and just slap it in the corner of the room.

If you are limited in terms of your placement, you should always try pulling the subwoofer out from being up against the corner. Even a couple of feet of pulling the subwoofer out from the corner can smooth out the bottom end significantly. Now, this may sound a little bit strange, but it really works. Then, connect it up as usual and play some music or movies that have some good little frequency content in them.

Subwoofers interact with rooms in a way that causes what are called room nodes which are peaks and valleys in the response. And these occur at different frequencies, depending on the room and where the subwoofer is placed.

Big Picture Big Sound

But even a shiny set of surround sound speakers might not be enough to earn you the title. You have to know how to precisely position those speakers and master the ins and outs of how to hook up surround sound to your TV. Plenty of people find themselves practically paralyzed when it comes to the prospect of running wires and angling speakers. Countless more have given it their best shot but found they could still use some pointers on maximizing their surround sound systems. Allow Klipsch give you everything you need to know about hooking up your surround sound system.

Setting up an audio system is a lot trickier today than it was many years ago. In the past, speakers were designed to reproduce bass frequencies, so the need for seperate subwoofers were non-existant.

A stereo system is a central part of most home theaters. Purists gush about the sound they can get from their stereo receivers and speakers. Consistent advancements in the music industry have made it possible to connect other playback devices besides just a CD player. MP3 players have established themselves as an especially practical option. An MP3 player offers room to store hundreds or thousands of music titles in a tiny space.

If you’re having a party at home, it’s possible for any guest in the room to play his or her own music at the drop of a hat.

How do you hook up your subs if it has 2 inputs?

Can’t find your answer? Get the answer Jan 31, , 6: Jan 31, , 6: If your amp is saying 8 ohms, and nothing on fine print is saying it can handle lower, then whatever you do, DO NOT make it see less than 8 ohms. So the receiver watt 2 Ch with connections for an A and a B set of speakers booklet shows:

Jan 14,  · You could buy a two-channel equalizer and hook your regular speakers up to one channel, and the subwoofer to the other channel And by doing that, you could cut the mids and highs off to the subwoofer while keeping the full range for the other speakers.

Speaker Connections for proper impedance match A note about amplifiers: You should always use the recommended load for your amplifier. However, if you must use a load other than the recommended load, here is a short guide. Most solid-state amplifiers would rather look at an open circuit no speaker at all than a load. Therefore, you can usually use a load that is higher than the recommended load. Do not use a lower impedance load, as this could cause serious damage to your SS amp.

On the other hand, most tube amplifiers need a load to avoid transformer or tube socket damage.

Help me hook up a passive subwoofer

Are you sure you want to delete this answer? Yes Sorry, something has gone wrong. There is no good way to do it. You’re planning to connect your subs where you should be connecting your full range speakers and you should not parallel the subwoofers with the full range speakers.

Feb 14,  · Odds are you won’t get under $ unless you stick to option number one, but if you do stick with number two, they’ll recommend products until you’re well over a grand. dot_hack_freak, .

How to hook up a subwoofer to a stereo system Hint: You don’t necessarily need a receiver with subwoofer output jacks. Subs can provide a foundation to the sound that few speakers can muster on their own. So adding a sub is not just about adding more and deeper bass; rather, a properly integrated subwoofer can improve the overall sound of the system. AV receivers feature bass management to direct the low bass frequencies to the sub and the midrange and treble frequencies to the speakers.

The subwoofer is hooked up to the receiver with a single interconnect cable. Stereo receivers, pre-amps, and integrated amplifiers rarely have subwoofer output jacks or offer bass-management options. So instead of using those connections, we’ll use the subwoofer’s speaker-level, aka “high-level,” inputs. Most, but not all, subwoofers have these inputs; they get connected using speaker cables to the same speaker output jacks on your receiver or amplifier that are also hooked up to your speakers.

That means you have to double up the connections on the receiver or amplifier see photo below that illustrates that connection method. The top picture has just the speaker cables connected to the stereo amp; the bottom picture has the speaker and subwoofer cables connected. The sub will use its built-in crossover aka “low pass” filter to determine the upper limit of the frequencies produced by the subwoofer.

With small speakers with 4-inch or smaller woofers, you’ll set the sub’s crossover frequency at Hz or higher, and with speakers with 5-inch or larger woofers, 80Hz or lower. Then set the sub’s volume control to provide the level of bass support you want.

ASK A BRAND

Connecting 8 pairs of speakers to 1 receiver Hook it up according to Tony’s directions and you won’t fry your amp, but you would in a parallel connection. Hooking up 8 speakers in series though would quickly clip your amp because of the 8X voltages it would be required to output. Are you using all 8 speakers all of the time?

The best way to hook up external speakers to your LG is through a home theater receiver. If you don`t have one, you`ll need to make sure that your LG has connections for external speakers. If it doesn`t you`re out of luck.

Receivers Introduction Throughout my life as a home theater enthusiast and reviewer, I have always preferred products that offer high value. I have generally interpreted that to mean the products are simple to set up and operate. Good sound quality is the main point, after all. I believed that anything which does not directly contribute to the primary objective was irrelevant, unnecessarily costly and would certainly degrade performance right?

This assessment appeared to be especially germane when considering amplifiers and pre amps. But, with modern product design enhancements, digital control technologies and efficient manufacturing and shipping, all that is changing. Now a high-value product can have tons of flexibility and features without sacrificing sound quality to any appreciable extent. So before me on this occasion is this modern surround sound receiver, the Integra DTR This means that the amplifier section should suffice to play at reference levels in home theaters of up to 2, cubic feet with a 10 — 12 foot viewing distance from the screen.

More on this later. Integra has maintained a similar styling aesthetic for their products throughout their year history.

Integra DTR-50.1 7.2 A/V Receiver

In the past, speakers were designed to reproduce bass frequencies, so the need for seperate subwoofers were non-existant. When the size of speakers began shrinking, the need for subwoofers to handle bass increased. In learning The ‘Bassics’ of Bass Management , you’ll discover that receivers figure out what speakers should get bass digitally, and send the appropriate bass information to a powered subwoofer using a line-level connection.

But before receivers were digital, bass management had to be handled by the subwoofer using a age-old technology. Subwoofers have undergone some serious change in the past decade. Intitially, most subwoofers were passive.

Can I hook two subwoofers to my soundbar? Buy a better sub, speakers, and receiver and start living a better life. You’re better than this OP. If the subs are powered, it’s probably fine. If not, only hook up one. Hooking up non-powered subwoofers the way you describe risks burning out the amp. Powered subs just get an audio signal and.

Originally Posted by Trogdor Thanks dd3mon. Okay, how will imaging be effected by a sub in the corner? Has anyone done this with with 2 sub’s on placed in both front corners? I’m considering getting an external sub for my 2 channel setup. My speakers do bass quite nicely tight and accurate but not booming though I’m about to change amplification drastically. Many sub manufacturers especially the cylindrical models such as SVS’s most popular line recommend corner placement.

Imaging should be not be affected unless your mains are extremely bass-light so the sub’s crossover has to be set very high. True low-bass somewhere around hz and below becomes very difficult to accurately locate the source of it. This means if your sub is only handling the lower frequencies, placement will just affect it’s output level and possible room resonances, not imaging. Of course, two subs one in each front corner is the optimal setup; However not all of us can afford these luxuries, and not all of us have rooms large enough to not be overwhelmed by the output of two subs -dd3mon Amp:

Best Rated in Home Audio Subwoofers

Second, try to be a bit more descriptive about what you have an what your problem is. What kind of surround sound system do you have? What kind of speakers are you trying to hook up to it?

Aug 24,  · I have four 12’s that i will be hooking up to a two channel home receiver.I know how to hook those up. I want to run small speakers for my four subs are 4ohm single voice : Resolved.

Friday, June 18, – The Sony DE series is their value line. My experience with this line of Sony receivers the , and during HT use is that the power supply is woefully inadequate and you might actually be getting 30 wpc rms rather than the advertised wpc when it is under the load of a 5. That is, driving 5 speakers the power supply appears to have substantial difficulty in powering all channels. You might actually get wpc during 2 channel stereo. While that is in HT, you are describing driving a substantially greater number of speakers.

I just don’t think this receiver is up to the task, is simply is not powered well enough. Because of this, I cannot imagine this receiver being able to run the load you describe. What you are suggesting doing is a substantial load for a receiver. My suggestion would be to quickly return that sony receiver.

For the money you paid for this, and assuming you want to stay with a receiver, try the yamaha htr , that will give you 95 wpc in ALL 7 channels. The power supply is excellent and this receiver can handly lower impedance loads that it would be likely to encounter in this set up.

Connect Two Subwoofers With One Music Source